IEC 60352 Solderless Connections

    IEC 60352 Introduction

    Poor connections may result in higher contact resistance, signal loss, or mechanical failure, which has an impact on the reliability of the entire system. Standard requirements have been developed by IEC 60352 regarding the design, installation, and performance testing of solderless connections. The standard was developed by the International Electrotechnical Commission and requires such connections to be economically sound and have the strength to resist mechanical stress and remain alive to electrical requirements.

    Read more

    Get Certified IEC 60352 for Reliable Electrical Connections

    The certification to IEC 60352 proves that solderless connections are in accordance with the international requirements of mechanical robustness and electrical performance. Compliance helps in the reliability of products, safety, and uniformity of electrical connections in hazardous uses.

    Scope of IEC 60352

    • Applies to solderless electric connections like crimped and wrapped terminals. 
    • Can be applied to electronic, automotive, and industrial electrical assemblies. 
    • Provides mechanical strength and electrical continuity of the terminations of conductors. 
    • Used in the qualification of products, in quality control during manufacturing, and also in conducting a reliability test.

    IEC 60352 Equipment and Sample Preparation

    Connection PreparationUse specified crimping tools or termination methods according to the connector design
    Specimen DetailPrepare representative conductor and terminal assemblies without damage or deformation
    CalibrationVerify measuring instruments for force, resistance, and environmental conditioning parameters

    Applications of IEC 60352

    • Electrical termination qualification of crimped and wrapped. 
    • Testing of the dependability of wiring harnesses on automotive and aerospace systems. 
    • Connector inspection of telecommunication equipment and electronics. 
    • Checking of the insulation displacement and compression-type connections. 
    • Reliable termination conductor technologies 
    • Research and development.

    IEC 60352 Common Challenges and Troubleshooting

    Some of the challenges are the inappropriate crimping force, wrong tool choice, and destruction of conductors or strands in termination. These problems can cause an augmented contact opposition or mechanical breakdown during loading. Laboratories solve these issues through calibrated crimping tools, outlined protocols of termination, and by visual and dimensional inspection before testing.

    Read more

    IEC 60352 Technique, Process, and Data Collection

    Taking this test consists of making solderless connections employing defined methods of termination, and mechanical and electrical testing. The strength tests of the pull-out test and the resistance test determine mechanical and electrical continuity, respectively. In order to assess long-term durability, environmental conditioning can be used. Some of the data gathered are the values of the pull forces, contact resistance, observation of the environmental exposure, and the failure.

    IEC 60352 Testing Procedure and Requirements

    Connection PreparationPrepare conductors and apply the appropriate solderless termination method
    Assembly VerificationInspect connection geometry and installation quality
    Mechanical TestingApply tensile or pull-out forces to verify mechanical strength
    Electrical Resistance TestMeasure contact resistance to confirm reliable conductivity
    Environmental ConditioningExpose connections to vibration, temperature cycling, or humidity as required

    IEC 60352 Analysis Results and Interpretation

    The outcome depends on the performance of the solderless connection in terms of mechanical retention and the reduced electrical resistance. Acceptable performance means that there is good electrical continuity and structural integrity. The high resistance or early mechanical breakdown indicates low termination or wrong tooling, and corrective measures are taken during the assembly procedures.

    Read more

    IEC 60352 Problem & Solution

    Problem: Bad solderless connections may result in electrical discontinuity, overheating, or mechanical failure of electronic assemblies.

    Solution: EC 60352 is a standard of requirements and test methods to confirm the mechanical strength and electrical reliability of solderless terminations.

    Updated on September 17, 2026

    Davis Scott
    About Author
    Davis Scott is an Electrical and Electronics Engineer specializing in multidisciplinary validation, quality assurance, and comprehensive electro-mechanical testing.
    Know More
    Testimonials
    Real results
    Engineers trust us with what matters most
    Why Choose Matestlab?
    Matestlab is a unified testing services partner based in the USA. Matestlab offers raw material and product testing services through accredited, expert laboratories primarily based in the USA. Matestlab supports physical, thermal, chemical, electrical, mechanical, environmental, and characterization testing needs through its global network of 2200+ accredited testing laboratories. Matestlab's in-house materials science experts curate and design comprehensive testing programs matched to the sample material and specific testing need, with regulatory requirements and confidentiality in mind.

    If you are looking for a managed and trusted testing partner to achieve your research goals, feel free to schedule a meeting with us or send us a request at connect@matestlabs.com to learn more about our services. For a quick quote, call us at (302)244-7710. We are happy to serve you.
    Start Your Testing
    Project Today
    Define your requirements and get access to
    specialized laboratories ready to deliver results
    Partners with us
    Clients
    Vendors
    Process for testing
    • STEP 01

      You share your testing requirements

    • STEP 02

      You share your sample(s)

    • STEP 03

      We deliver your test reports

    Get your testing done

    Let us know your testing requirements and we will be right back with a solution.

      Let us root for each other. Collaborate to grow, expand, and accelerate our businesses.

      Partner with us